All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. 

The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life.

During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicon Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. 

The balls are held in place by a reinforced polyamide cage. Every bearing is optimised with a low viscosity CeramicSpeed “Blue Grease” to minimise fiction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross and MTB. The benefits are super low friction, better power transfer and increased bearing life.

During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads and are 100% smoother.

Description 

Campagnolo Stainless Steel Cartridge Bearing kit (pair)
Standard equipment on 2009 & later Chorus cranksets & Pre 2011 Record UT Cranksets
Fits all Campy Ultra Torque Cranksets
Campagnolo Part # FC-RE012

DESCRIPTION

ACTIVE

SEALED BOTTOM BRACKET

Sealed bottom bracket KLS ACTIVE is made for all bikes which has cranks with common square bottom bracket mount

DETAILS

Sealed bearing

Square Taper chainwheel mount

BSA: BC1.37"x24T R/L 68mm

Nylon cups

2 Allen screws

Narrowed mid-section for internal routing

OPTIONS

Color: Black

Length: 126; 124,5; 122,5; 119; 117,5; 116; 113; 110mm

INCLUDED

Nylon cups

2 Allen screws

COMPATIBILITY

Bicycles which has cranks with common square bottom bracket mount

For the Pressfit bearing standard: the bottom bracket by Truvativ

Pressfit bottom brackets use the same bearing technology as the current GXP bottom brackets and offer the same performance in terms of durability and longevity. Pressfit bottom brackets are not screwed into the bicycle frame, as is usual with GXP bottom brackets, but are pressed into the frame.

Technical Information:

Application:

MTB, Road

Cup Material:

composite material

Fitting:

BB86, BB92

Shell Diameter:

41 mm

Shell Width:

86.5mm / 89.5 - 92mm

Bearings:

cartridge w/ steel balls (standard)

Compatibility:

only for Pressfit frames

Size Guide:

Road:

• Application: Road
• Bottom Bracket Standard: BB86
• Shell Width: 86.5 mm
• Manufacturer Number: 00.6415.033.000

MTB:

• Application: MTB
• Bottom Bracket Standard: BB92
• Shell Width: 89.5 - 92 mm
• Manufacturer Number: 00.6415.033.020

Contents:

• 1 x Truvativ GXP Pressfit right bearing cup, incl. bearings
• 1 x Truvativ GXP Pressfit left bearing cup, incl. bearings
• 1 x Truvativ GXP Pressfit centre tube

or the Pressfit bearing standard: the bottom bracket by Truvativ

Pressfit bottom brackets use the same bearing technology as the current GXP bottom brackets and offer the same performance in terms of durability and longevity. Pressfit bottom brackets are not screwed into the bicycle frame, as is usual with GXP bottom brackets, but are pressed into the frame.

Technical Information:

Application:

MTB, Road

Cup Material:

composite material

Fitting:

BB86, BB92

Shell Diameter:

41 mm

Shell Width:

86.5mm / 89.5 - 92mm

Bearings:

cartridge w/ steel balls (standard)

Compatibility:

only for Pressfit frames

Size Guide:

Road:

• Application: Road
• Bottom Bracket Standard: BB86
• Shell Width: 86.5 mm
• Manufacturer Number: 00.6415.033.000

MTB:

• Application: MTB
• Bottom Bracket Standard: BB92
• Shell Width: 89.5 - 92 mm
• Manufacturer Number: 00.6415.033.020

Contents:

• 1 x Truvativ GXP Pressfit right bearing cup, incl. bearings
• 1 x Truvativ GXP Pressfit left bearing cup, incl. bearings
• 1 x Truvativ GXP Pressfit centre tube

A variant of the BB30 design: the Press Fit 30 Bottom Bracket by FSA

Press fit refers to one of the newer bottom bracket standards, and was first introduced to the market by SRAM as Press Fit 30. The bearings are located in bearing cups that are pressed directly into the bottom bracket shell. Characteristic is the installation dimension of 46 mm and the shell width of 68 / 73 mm or 86.5 mm. A PF30 bottom bracket always takes only one axle with 30 mm diameter - hence the name.

Specifications:

Application:

Road, Cross Country

Type:

Press Fit PF30, BB386EVO

Shell Diameter:

46 mm

Shell Width:

68-86.5 mm

Axle Diameter:

30 mm

Technical Information:

Bearings:

steel or ceramic

Compatibility:

• BB30 Road cranks
• BB386EVO cranks*

* when installed in a BB386EVO frame. If a BB386EVO crank is to be mounted in a Press Fit 30 frame, an additional MW258A adapter is required.

Note:
The 200-3112 bottom bracket also does the following:

• Installation of FSA MegaExo NBD, MegaExo Pinch Bolt, Shimano and SRAM GXP Road cranks in BB386EVO frames
• Installation of FSA MegaExo NBD, MegaExo Pinch Bolt and Shimano Road cranks in Press Fit 30 frames
• Installation of FSA BB386EVO, MegaExo NBD and MegaExo Pinch Bolt Road cranks in Cannondale press fit 30A 73 mm frames
• • nstallation of FSA BB386EVO Road cranks in BBRight Press Fit 79 mm frames
  • Installation of FSA BB392EVO, MegaExo NBD 24 mm, MegaExo NBD 19 mm, MegaExo Pinch Bolt 24 mm and Shimano MTB cranks in 68/73 mm PF30 frames
  Additional adapters and spacers are required.
  
  The 200-3111 bottom bracket also does the following:
  
  • Installation of FSA MegaExo NBD Road cranks in BB386EVO frames
  • Installation of FSA MegaExo NBD Road cranks in Press Fit 30 frames
  • Installation of FSA BB392EVO, MegaExo NBD 24 mm, MegaExo Pinch Bolt 24 mm and Shimano MTB cranks in 68/73 mm PF30 frames
  Additional adapters and spacers are required.
  

Models:

Standard:

• Bearings: steel
• Recommended Cranks: SL-K Light, Energy, Gossamer Pro, Omega, Vision TriMax Pro
• Model Number: BB-PF6000/CZ
• Manufacturer Number: 200-3112

ceramic:

• Bearings: ceramic
• Recommended Cranks: K-Force Light, TriMax Carbon TT
• Model Number: BB-PF8200/CZ
• Manufacturer Number: 200-3111